无码中文字幕久久无码_国产av巨作精品原创_中文字幕无码人妻精品_无码一区中文字幕在线观看

NOTES注釋:
1.       THE FOLLOWING PHOTOPLOT FILES(.PHO),APERTURE REPORT FILES(.REP), NCDRILL, AND LAYER LIST(.LST) FILES ARE REQUIRED TO FABRICATE THIS PCB:
以下PHOTOPLOT文件（.PHO），光圈報告文件（.REP），NCDRILL
層列表（.LST）文件用于制造該P(yáng)CB：
8030122-P1.PHO/COPPER, LAYER 1 TOP SIDE銅箔，頂層
8030122-P2.PHO/COPPER, LAYER 2 BOTTOM SIDE銅箔，底層
8030122-P3.PHO/PASTER MASK, TOP SIDE鋼膜，頂層
8030122-P4.PHO/SOLDER MASK, TOP SIDE阻焊，頂層
8030122-P5.PHO/SOLDER MASK, BOTTOM SIDE阻焊，底層
8030122-P6.PHO/SILKSCREEN, TOP SIDE絲印，頂層
8030122-P7.PHO/DRILL DRAWING鉆孔圖
8030122-P8.PHO/ASSEMBLY DRAWING裝配圖
8030122-P9.DRL/NC DRILL DRAWING NC鉆孔圖
8030122-P9.LST/NC DRILL DRAWING NC鉆孔圖
8030122-P.REP/APERTURE FILE光圈文件
8030122-P.LST/LAYER LIST層列表
2.       MATERIAL材料:
FR-4 FINISHED TO 0.062 +/- 0.006 THICK
FR- 4  成品0.062 +/- 0.006（英寸）
3.       COPPER PLATE銅板:
COPPER LAMINATION IS 1 OZ.PLATED TO 1.5 OZ. FOR OUTSIDE LAYERS.
銅層壓1 OZ.電鍍后為1.5盎司。適用于所有外層。
4.       CONDUCTOR WITH AND SPACING導體和間距:
THE MINIMUM CONDUCTOR WITH AND SPACING ON THE FINISHED BOARD IS成品板最小導體間距:
WIDTH線寬– 6 MIL
SPACING線寬– 6 MIL
5.       HOLE REQUIREMENTS孔要求:
PLATED THROUGH HOLES TO BE +/-0.003 OF DEFINED SIZE AFTER REFLOW鍍通孔過回流焊后為定義尺寸的+/-0.003英寸.
HOLE LOCATION TO BE +/-0.003 RELATIVE TO LOCATING REFERENCE孔位置為相對定位參考點的+/-0.003英寸.
6.       SOLDER MASK阻焊:
SOLDER MASK OVER BARE COPPER阻焊蓋過裸銅.
MATTE GREEN SOLDER MASK APPLIED TO BOTH SIDES雙面使用亞光綠色阻焊面膜.
7.       MARKING標記:
WHITE INDELIBLE SILKSCREEN APPLIED TO COMPONENT SIDE元器件層使用白色、不可擦除絲網印刷.
VENDOR LOGO FLAME RATING TO BE APPLIED IN COPPER ON SOLDER SIDE, 0.160 MIN. FROM ALL PADS, TRACES AND EDGES廠商標志阻燃等級適用于銅焊接層，最小0.160英寸。用于所有焊盤、印制線和邊緣.
8.       MANUFACTURER TO BE U.L. RECOGNIZED, MANUFACTURE IN ACCORDANCE WITH PERFORMANCE STANDARD IPC-6011 & IPC-6012, TYP3, CLASS 2制造商為UL認可制造商，制造按照績效標準IPC- 6011和IPC- 6012，TYP3，2級執行.
9.       NO MODIFICATION OR REPAIRS ARE PERMITTED WITHOUT APPROVAL未經許可，不得進行修改或維修.
AFTER APPROVAL MODIFICATIONS TO BE MADE IN ACCORDANCE WITH IPC-771 & IPC-7721被批準后，按照IPC- 771和IPC- 7721執行修改或維修.
10.   ALL PERIMETER DIMENSIONS IN INCHES +/-0.010所有外圍尺寸公差+/-0.010（英寸）.
11.   TEST 100% FOR ELECTRICAL SHORTS AND OPENS(IF APPLICABLE) 盡可能100%測試電氣開短路.